PEAVEY ECOUSTIC E110 | ตู้แอมป์อคูสติค Acoustic Amplifier 10″ 100W
ตู้แอมป์สำหรับกีตาร์อคูสติค Peavey Ecoustic E110, กำลังขับ 100 วัตต์ ดอกลำโพงขนาด 10 นิ้ว, 2-independent channels, 9-band graphic EQ on ch 1, 2-band EQ on ch 2, 8 effect presets, Premium mic preamp
The Ecoustic E110 Acoustic Amplifier from Peavey is a versatile amplification system designed for acoustic instruments, vocals, and line-level devices such as samplers and audio players in performance and rehearsal applications.
It provides 100W of clean power into a bi-amplified system containing a 10″ full-range loudspeaker and a high-frequency horn. Both channels operate independently, with 9-band graphic EQ on channel 1 and 2-band adjustment on channel 2, a Notch Filter and Phase Inverter on channel 1 to control feedback, foot-switchable Mute/Tuner, and more.
The master section includes digital reverb, chorus, and delay with channel assignment and parameter adjustment, and the foot controller (sold separately) allows users to access up to 8 presets plus an onboard looper.
Features
- Two independent channels
- 1 x 10 full-range loudspeaker plus 1 high-frequency horn
- 9-band graphic EQ on channel 1 Combo XLR-1/4″ input on each channel
- Foot-switchable Phase inverter for controlling feedback
- Notch Filter on channel 1 for controlling feedback Two-band EQ on channel 2
- Master volume Reverb, chorus, and delay with parameter adjustments
- Advanced WYSIWYG (What You See Is What You Get) technology
- Premium mic preamp Foot-switchable tuner/mute out
- Up to 8 effect presets with foot controller (foot controller sold separately)
- Onboard looper with foot controller (foot controller sold separately)
- Pole mount (1 1/2″ internal diameter) 100W of power
Specifications
Rated Power |
100 W into 8 Ω load (internal with DDT compression) |
Frequency Response |
+0, -3 dB, 20 Hz to 20 kHz @ 60 Wrms into 8 Ω |
Total Harmonic Distortion |
<0.5%, 1 to 50 Wrms, 20 Hz to 20 kHz, 8 Ω |
Dynamic Range |
DDT: >20 dB |
Maximum THD @ 1kHz |
DDT: <0.5% THD for 6 dB overload <1% THD for 20 dB overload |
Hum and Noise |
>90 dB below rated power |
Power Consumption |
150 W, 60 Hz, 120 VAC (domestic) 150 W, 50/60 Hz, 220 to 240 VAC (export) |
Settings |
The following specs are measured @ 1 kHz with the controls preset as follows: Channel 1 Gain @ 5 Graphic EQ Sliders @ 0 dB Notch Filter @ 0 dB Channel 2 Gain @ 5 Low EQ @ 0 dB High EQ @ 0 dB All Effects Bypassed Master Volume @ 5 |
Input |
For Channel 1: 1/4″ Input: Impedance: High Z, 10 MΩ Nominal Input Level: -8.40 dBV, 380 mVrms Maximum Input Level: 3.52 dBV, 1.50 Vrms XLR Input: Impedance: Low Z, 8.2 kΩ Nominal Input Level: -25.1dBV, 55.8 mVrms Maximum Input Level: -13.2 dBV, 220 mVrmsFor Channel 2: 1/4″ Input: Impedance: High Z, 10 MΩ Nominal Input Level: -8.40 dBV, 380 mVrms Maximum Input Level: 3.52 dBV, 1.50 Vrms XLR Input: Impedance: Low Z, 8.2 kΩ Nominal Input Level: -25.1 dBV, 55.8 mVrms Maximum Input Level: -13.2 dBV, 220 mVrms |
Equalization |
Channel 1: Nine-band, Constant-Q Graphic EQ Frequency Centers (Hz) at 63, 125, 250, 500, 1k, 2k, 4k, 8k, 16k Available ±15 dB of boost/cut on each band Channel 2: Low and High Shelving-type EQ Corner Frequencies at 80 Hz and 8 kHz, respectively Available ±15dB of boost/cut on eachBalanced XLR Line Output (Rear): Output Impedance: 150 Ω Nominal Output Level: 3.23dBV, 1.45 Vrms Available Ground Lift capability System Hum & Noise @ Nominal Input Level: >75 dB below rated power (20 Hz to 20 kHz un-weighted) |
Filter |
Notch Filter: Channel 1: Available 18 dB of cut at 150 Hz |
Dimensions (H x W x D) |
18.0 x 20.7 x 14.7″ (457.2 x 525.8 x 373.4 mm) |
Weight |
45.0 lb (20.4 kg) |